Support 23 S
1.77–3.1 m · 7.2 kg 5.8–10.2 ft · 15.9 lbs
I recommend these products to all who work not only with wood but concrete and even steel as well.
Trusted by



Support 35
Our longest yet still very lightweight steel wall brace. Recommended for walls up to 16 – 23 ft where high precision and stability are required. Developed for demanding weather conditions and varied installations – robust, reliable, and built to resist rust and looseness even after long, heavy use.
Answer 3 questions and we pick the model for your wall.
A starting point, not a structural calculation. Check the load table, and have the bracing verified by the responsible engineer.
Model
Why crews love it:
🚚
On site in 25+ countries and in rental fleets.
🛡️
Use them on a job. If they are not right, send them back.
On a real job with 3 guys and a large crane, the walls went up 50% faster than with 2×4s.
4 h
saved for 3 guys and a crane. That is about $1,980 on one job.
Why: a 2×4 is cut, nailed and re-nailed, with no fine adjustment. A brace is turned until the wall is plumb. Counted at $90 per hour per person and $225 per hour for the crane.
Details
| Length | 2,850–4,970 mm |
| Rough adjustment | 100 mm |
| Weight | 18 kg |
| Locking pins | 2 |
| Bracing angle | 30°–60° |
Stedox® Support 35 · 2.85–4.97 m · 18 kg
| Length [m] | 3.0 | 3.5 | 4.0 | 4.5 | 5.0 |
|---|---|---|---|---|---|
| Permissible load [kN] | 12 | 9 | 7 | 5.8 | 4.7 |
Allowable loads include a safety factor of 1.5. Values are based on Eurocode 3 calculations and laboratory tests. All loads must be calculated by a qualified engineer; the brace angle must be between 30° and 60°.
For engineers · Technical documents
Also available: end bracket ultimate loads with Simpson Strong-Tie® fasteners, in timber and concrete.
Stedox® Support 35 is a wall brace used to erect and install prefabricated elements, panels and columns. It was developed from the ground up to be safe, durable and easy to handle.
Extend it in 3.94″ steps, lock it with the locking pin, attach it to the wall and floor, then rotate the brace to fine-adjust it to plumb. Rust protection: Strip galvanized tubes, powder coated, for a long life in wet and harsh conditions.
What’s included
How it works
Four steps, one person. Read the full operating instructions before first use.
Pull the telescopic tube out to roughly the length you need. It adjusts in 3.94″ steps.
Put all 2 locking pins through the tube. Never load the brace without them.
Fasten both end brackets securely, at an angle of 30°–60° and above the centre of gravity of the wall.
Rotate the brace by the handle until the wall is plumb. The built-in stop keeps the threads from unscrewing.
We built these braces after years on site, and we answer for them ourselves. If something is not right, you talk to us directly.
wall braces sold
Every one shaped by feedback from rental companies, installers and carpenters.
Just as easy as I imagined.
Jonny
We couldn’t be happier with the quality of Stedox tools. The boys at Wallstreet Carpentry are hard on our tools and rely on them to last.
Devin D., Wallstreet Carpentry
Every benefit at a glance. Pick one to see the Stedox way next to the alternative.
Tap the right side for the next one, the left side to go back.
Stedox wall braces 1 / 11
Built-in stop
All our braces are manufactured with a built-in stop function for safety and reliability reasons.
Stop mark
A decal on the tube shows the moment the brace is at its maximum length.
High-visibility yellow
The yellow powder coat makes every brace easy to see on a busy site.
Double rust protection
Every tube is hot-dip galvanized and then powder coated.
High clearance
Even lying flat, the brace hovers above the ground on its end brackets.
Forged threaded rod
The threaded rod and its ball head are forged as one part.
Extra sturdy handle
A CNC-machined aluminium handle on a U-bracket welded at two points.
Quick rough adjustment
Rough length is set in 3.94″ steps with 2 quick locking pins.
Easy fastening
A bigger end bracket with more holes and more hole types.
Wider working angle
High clearance gives the brace room to work at steeper angles.
Many ways to attach
The end brackets attach to floors, walls, edges and beams.
We recommend · Aluminium
Support 23 S
1.8–3.1 m · 7.2 kg
Low wind loads and a floor bracket close to the wall: the light steel brace does the job.
Brace length needed: about 2.6 m
Permissible load at this length: about 5.7 kN along the brace, 4.0 kN horizontally at 45°. Includes a safety factor of 1.5.
The operating instructions recommend attaching at 3/4 of the wall height or higher.
Always use at least two braces per element.
Check out Support 23 SThis is only a recommendation. Always check with your engineer before choosing a brace, and follow the permitted loads in the operating instructions.
| Model | Material | Length | Weight | Price | Best for |
|---|---|---|---|---|---|
| Support 23 S | Steel | 1.77–3.10 m | 7.2 kg | Ask for a price | Walls up to 3 m, lower wind loads |
| Support 23 | Steel | 1.95–3.38 m | 13.2 kg | Ask for a price | Higher wind loads, sheeted walls |
| Support 35 | Steel | 2.85–4.97 m | 18 kg | Ask for a price | Taller walls, bracket far from the wall |
| ALU-Support 47 | Aluminium | 3.92–6.97 m | 33 kg | Ask for a price | Walls over 5 m |
Volume pricing for projects and fleets. Reply within 1 business day.
1.77–3.1 m · 7.2 kg 5.8–10.2 ft · 15.9 lbs
1.95–3.38 m · 13.2 kg 6.4–11.1 ft · 29.1 lbs
2.85–4.97 m · 18 kg 9.4–16.3 ft · 39.7 lbs
3.92–6.97 m · 33 kg 12.9–22.9 ft · 72.8 lbs
0.98–6.97 m · 31 kg 3.2–22.9 ft · 68.3 lbs
Add your first brace
Tap + Add to quote on a brace on the left, or drag a card into this box.
Tap + Add on a brace below.
Would you like a quote on our beam pullers as well? Set a quantity for any you are interested in — or just send your request.
Reply with pricing within 1 business day.
We will get back to you within 1 business day.
Rent them instead?
Tell us the country, the braces and the dates. We check availability and put you in touch with the rental partner.
Used on jobsites in 25+ countries, across Europe, North America and beyond. Tag @stedox_official and your site might end up here.
Messages, comments and reviews from crews who use the braces on their own jobs.
100% money-back guarantee.
Saul
E-com manager
Free field guide
Where the bottom bracket goes decides how fast you brace. Six fastening methods crews use on the ground or floor.
One email with the PDF. No spam, unsubscribe anytime.
It depends on the wall height and the wind loads. Use “Which brace for which wall?” on this page, or send us your wall heights and we will tell you.
Always at least two wall braces per element. How many more depends on the loads, which a qualified engineer must calculate for your project.
The allowable axial loads by length, including a safety factor of 1.5, are in the load table on this page. The full load tables are in the operating instructions.
We ship internationally. If you can’t order directly from our site, email Saul at saul@stedox.com and he will help you out. Shipping is calculated at checkout; for a project or fleet order, ask us for a delivered price.
Yes. Message us on WhatsApp with your wall heights and quantities and we will send a project price.
Visa, Mastercard, Maestro, American Express, Diners Club, PayPal, Apple Pay and Google Pay.









